Effect of pore diameter variation of FeW/SBA-15 supported catalysts on hydrotreating of heavy gas oil from Athabasca bitumen
Boahene, Philip Effah
The pore diameter of a catalyst support controls the diffusion of reactant molecules to the catalytic active sites; thus, affecting the rates and conversions of the hydrotreating reactions. Desirable textural properties of SBA-15 makes it a potential alternative to the conventionally used γ-Al2O3 support due to the fact that its pore size can be manipulated via controlling the synthesis parameters, while maintaining relatively high surface area. Larger pore diameter SBA-15 supports may facilitate the diffusion of bulky molecules as that of the asphaltenes present in the heavy petroleum fractions, making it a potential catalyst support for hydrotreating operations. Considering the very sour nature of Canada’s bitumen with high sulfur contents in the range of 2-6 wt %, the appreciably high sulfur contents particularly present in Athabasca derived heavy gas oils (about 4 wt % sulfur), the rising demand for cleaner fuels, and also the increasing stringency on environmental standards, the need for novel and improved hydrotreating catalysts cannot be overemphasized. By varying the molar ratio of hexane to ammonium fluoride, the pore channels of SBA-15 could be varied. Controlling the pore diameter of these supports via micelle swelling facilitated the production of larger pore diameter SBA-15-supported catalysts. In this project, four mesoporous silica SBA-15 catalyst supports with pore diameters in the range of 5-20 nm were synthesized in the preliminary phase using hexane as the micelle swelling agent and subsequently utilized for the loading of 2 wt.% Fe and 15 wt.% W catalyst metals, respectively. The hexagonal mesoscopic structure of these materials were characterized using powder small-angle X-ray scattering (SAXS), N2 adsorption-desorption isotherms, TEM and SEM images. Powder XRD analysis evidenced inhomogeneous metal dispersion on the largest pore diameter catalyst. An optimum pore diameter of 10 nm was found for Cat-B and subsequently used to obtain the optimum Fe and W loadings required to achieve the best hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) activities. The optimum catalyst was found to be Cat-H with metal loadings of 3 wt.% Fe and 30 wt.% W. At these loadings and temperatures of 375°C, 388°C, and 400°C, HDS activities of 53.4%, 64.1%, and 73.3% with corresponding HDN activities of 21.9%, 26.2%, and 38.3%, respectively, were recorded. Catalytic performance evaluations conducted on equal mass loading using a reference commercial γ-Al2O3-supported FeW catalyst offered HDS activities of 69.3%, 80.4%, and 89.1%, with corresponding HDN activities of 16.4%, 32.4%, and 49.3% at the same temperatures studied. However, no significant changes in HDS and HDN activities were observed for similar evaluations on volume percent metals loading basis. Kinetic studies performed with the optimum FeW/SBA-15 catalyst suggested activation energies of 147.2 and 150.6 kJ/mol for HDS and HDN, respectively, by the Langmuir-Hinshelwood’s model. Similar results were predicted by the Power Law and Multi-parameter models for HDS (129.6 and 126.7 kJ/mol, respectively), which does not conclusively make the latter model clearly stand out as the best. Data fitting by the Power Law suggested reaction orders of 2 and 1.5 for HDS and HDN, which seem to be consistent for the hydrotreatment of heavy gas oil. Finally, a long-term deactivation study spanning a period of 60 days time-on-stream showed the optimum catalyst to be stable under hydrotreating experiments conducted in a downward flow micro-trickle bed reactor at temperature, pressure, liquid hourly space velocity (LHSV), and gas/oil ratio of 375–400˚C, 8.8 MPa, 1h-1, and 600 mL/mL (at STP), respectively.
DegreeMaster of Science (M.Sc.)
SupervisorAdjaye, John; Dalai, Ajay K.
CommitteeWilson, Lee D.; Soltan, Jafar M.; Wang, Hui
Copyright DateApril 2011
heavy gas oil